PMU

HAL PMU提供抽象的軟件接口操作硬件PMU(Power Management Unit)模塊，提供的功能有:

• 設置芯片的供電參數
• 設置低功耗時鐘參數，
• 配置芯片進入關機模式并設置喚醒源, 在關機模式下芯片可被PIN和RTC喚醒, 喚醒PIN與GPIO管腳的映射關系與LPSYS睡眠模式的喚醒PIN相同，參見AON
• SF32LB52X支持充電，相關接口為 HAL_PMU_ChgInit 等

詳細的API說明參考 PMU.

Note

• HAL_PMU_CheckBootMode 需要在每次啟動時執行以獲取開機模式并清除相應狀態，如果關機狀態醒來不清PMU的狀態， 就無法調用 HAL_PMU_EnterHibernate 再次關機
• 執行 HAL_PMU_EnterHibernate 后芯片并不會馬上關機, 最長會延遲一個LP Clock周期才會關機, 這期間CPU還能繼續執行指令和響應中斷， 為避免中斷觸發后誤執行一些操作, 建議在調用 HAL_PMU_EnterHibernate 前關閉中斷, HAL_PMU_EnterHibernate 本身會是一個死循環, 永遠不會退出

使用HAL PMU

使能RTC和PIN喚醒后關機

void shutdown(void)
{
    /* Enable PIN0 low level wakeup  */
    HAL_PMU_EnablePinWakeup(0, 1);
    /* Enble RTC wakeup */
    HAL_PMU_EnableRtcWakeup();
    /* Disable Interrupt */
    
    /* Shutdown, can be wakeup by PIN0 and RTC */
    HAL_PMU_EnterHibernate();
    
}
 
/* Use HAL_PMU_CheckBootMode in initializtion stage to check whether it's cold boot or wakeup from shutdown mode */
void init(void)
{
    PMU_BootModeTypeDef boot_mode;
    uint32_t wakeup_src;
    /* check boot mode and clear PMU shutdown state if wakeup from shutdown mode
     */
    HAL_PMU_CheckBootMode(&boot_mode, &wakeup_src);
}

配置充電

static PMU_ChgHandleTypeDef pmu_chg_handle;
 
static void pmu_chg_callback(PMU_ChgHandleTypeDef *handle, uint32_t status)
{
    if (status & (1 << PMU_CHG_IRQ_VBUS_RDY))
    {
        printf("vbus: %d", HAL_PMU_ChgReadStatus(handle, PMU_CHG_IRQ_VBUS_RDY));
    }
 
    if (status & (1 << PMU_CHG_IRQ_EOC))
    {
        printf("eoc: %d", HAL_PMU_ChgReadStatus(handle, PMU_CHG_IRQ_EOC));
    }
 
    if (status & (1 << PMU_CHG_IRQ_VBAT_HIGH))
    {
        printf("vbat high: %d", HAL_PMU_ChgReadStatus(handle, PMU_CHG_IRQ_VBAT_HIGH));
    }
}
 
void config_charger(void)
{
    PMU_ChgCalParamTypeDef cal_param;
    uint32_t current;
    uint32_t volt;
    
    //config calibration data for charger, calibration is saved in EFUSE
    //cal_param.cc_mn = xxx;
    //cal_param.cc_mp = xxx;
    //cal_param.bg = xxx;
    //cal_param.cv_vctrl = xxx;
    //cal_param.rep_vctrl = xxx;
    status = HAL_PMU_ChgInit(&pmu_chg_handle, &cal_param);
    
    // config CC current
    current = 300; //300mA
    current = HAL_PMU_ChgConfigCcCurrent(&pmu_chg_handle, current);
    
    // config target voltage
    volt = 4300;  //4300mV
    volt = HAL_PMU_ChgConfigTargetVolt(&pmu_chg_handle, volt);
 
    // enable IRQ and register callback
    HAL_PMU_ChgRegisterCallback(&pmu_chg_handle, pmu_chg_callback);
    status = HAL_PMU_ChgConfigIRQ(&pmu_chg_handle, PMU_CHG_IRQ_VBUS_RDY, PMU_CHG_IRQ_TRIG_MODE_DOUBLE_EDGE);
    RT_ASSERT(HAL_OK == status);
    status = HAL_PMU_ChgConfigIRQ(&pmu_chg_handle, PMU_CHG_IRQ_VBAT_HIGH, PMU_CHG_IRQ_TRIG_MODE_POS_EDGE);
    RT_ASSERT(HAL_OK == status);
    status = HAL_PMU_ChgConfigIRQ(&pmu_chg_handle, PMU_CHG_IRQ_EOC, PMU_CHG_IRQ_TRIG_MODE_POS_EDGE);
    RT_ASSERT(HAL_OK == status);
 
    HAL_NVIC_SetPriority(PMUC_IRQn, 5, 0);
    HAL_NVIC_EnableIRQ(PMUC_IRQn);    
}